20x20 Concrete Slab Cost in 2026: Pad, Garage Floor, 20x30 and 20x40 Prices
Photo: Massachusetts Metropolitan District Water Supply Commission (1938), Wikimedia Commons, public domain
Quick Answer
The typical 20x20 concrete slab cost in 2026 is about $1,600 to $3,200 installed for a standard 4 inch slab, based on $4 to $8 per square foot. A 20x20 garage slab that is 5 to 6 inches thick with rebar and thickened edges usually costs more, often around $2,400 to $4,000 or higher. The slab needs about 5 cubic yards of concrete at 4 inches. A 20x30 concrete slab costs about $2,400 to $4,800, and a 20x40 concrete pad about $3,200 to $6,400.
A 20 by 20 foot slab, 400 square feet, is the classic size for a two-car parking pad, a small detached garage, a carport, a workshop, a large patio or a base for a prefab metal building. It is big enough that a ready-mix truck is the practical choice, but small enough that a single truck usually covers it.
This guide covers the 20x20 concrete slab cost for different thicknesses and finishes, what goes into a 20x20 concrete pad cost, how much concrete it takes, what a 20x30 slab, a 20x40 pad and a 20x30 metal building with a concrete slab cost, and how to save. Price ranges come from Angi, HomeAdvisor and HomeGuide, listed in the sources.
20x20 Concrete Slab Cost at a Glance
| 20x20 slab type | Cost per sq ft | Total for 400 sq ft |
|---|---|---|
| Basic 4 in. pad, broom finish | $4 – $8 | $1,600 – $3,200 |
| 5 – 6 in. garage slab with rebar | about $6 – $10 | about $2,400 – $4,000 |
| Colored or stained | $8 – $12 | $3,200 – $4,800 |
| Stamped patio | $12 – $18 | $4,800 – $7,200 |
| Remove old slab first (added) | $2 – $6 | $800 – $2,400 |
HomeAdvisor puts the average slab near $6 per square foot, which makes about $2,400 a good middle estimate for a plain 20x20 concrete pad. High-cost metro areas and difficult sites can push prices above these ranges, so treat them as a starting point and get local quotes.
How Much Concrete Does a 20x20 Slab Need?
| Thickness | Cubic feet | Cubic yards | With 5 – 10% extra | Ready-mix at $125 – $200/yd |
|---|---|---|---|---|
| 4 in. | 133 | 4.94 | 5.2 – 5.4 | about $650 – $1,080 |
| 5 in. | 167 | 6.17 | 6.5 – 6.8 | about $810 – $1,360 |
| 6 in. | 200 | 7.41 | 7.8 – 8.2 | about $975 – $1,640 |
All three fit in a single standard ready-mix truck, which usually carries about 8 to 10 yards. At 4 inches, you may be just above many plants' minimum order, so short-load fees are less likely than on a small pad. See how many yards of concrete are in a truck and concrete price per yard.
What Is Included in a 20x20 Concrete Pad Cost
A full installed price for a 20x20 concrete pad usually covers:
- Excavation and grading: removing sod and topsoil, digging to depth, and shaping a slope for drainage.
- Gravel base: about 4 inches of compacted crushed stone, roughly 5 cubic yards for 400 square feet.
- Forms: about 80 linear feet of edge forms, staked and set to grade.
- Reinforcement: wire mesh, fiber, or rebar on chairs.
- Vapor barrier for garages and enclosed buildings.
- Concrete: about 5 to 8 cubic yards depending on thickness.
- Placing and finishing: screeding, floating, edging, troweling or brooming.
- Control joints: typically dividing the slab into four 10 × 10 foot panels for a 4 to 5 inch slab.
- Curing and cleanup, including form removal.
Ask each contractor to list these items. Missing items, such as a thin base or no reinforcement, are often why one 20x20 concrete slab cost quote is much lower than the others.
20x20 Garage Slab Cost
A 20x20 garage slab is more than a plain pad. Building codes and good practice usually call for:
- Thicker concrete, often 4 to 6 inches, with rebar or heavy mesh.
- Thickened edges or footings around the perimeter to support the walls. In frost areas, footings may need to go below the frost line, or the slab may be designed as a frost-protected shallow foundation.
- Anchor bolts set in the wet concrete to hold the wall plates.
- A vapor barrier under the slab.
- A slope toward the door so water and melting snow drain out.
- A smooth trowel finish, which many owners prefer indoors.
- Permits and inspections, which most towns require for a garage.
Because of these extras, a 20x20 garage slab often costs about $2,400 to $4,000 or more, compared with $1,600 to $3,200 for a basic pad. If the garage needs deeper footings or a monolithic slab with integral footings, the price can be higher. For footing prices, see concrete footing cost.
20x30 Concrete Slab Cost
A 20x30 concrete slab is 600 square feet. At $4 to $8 per square foot, the 20x30 concrete slab cost is about $2,400 to $4,800 for a 4 inch slab. It needs about 7.4 cubic yards at 4 inches, 9.3 yards at 5 inches, or 11.1 yards at 6 inches. A 6 inch 20x30 slab may need a second truck or a larger truck. This size is popular for a two-car garage with a workbench area, a small shop, or a covered RV or boat pad.
20x30 Metal Building With Concrete Slab Cost
A 20x30 steel building on a concrete slab is a common shop or garage setup. HomeGuide puts prefab metal buildings at about $10 to $25 per square foot for the kit alone, or roughly $20 to $50 per square foot installed including foundation and assembly. For a 20x30 building (600 square feet), that suggests:
| Part | Estimate for 20x30 |
|---|---|
| Metal building kit ($10 – $25/sq ft) | about $6,000 – $15,000 |
| Concrete slab, 4 – 6 in. with thickened edges | about $2,400 – $6,000 |
| Building erection, doors, extras | varies widely |
| All-in installed ($20 – $50/sq ft) | about $12,000 – $30,000 |
The slab for a metal building must be designed for the building's anchor bolt pattern and loads, so get the building supplier's foundation drawings before you pour. Many metal building slabs use thickened edges or perimeter footings where the columns sit. Wind and snow loads in your area can change the anchor and footing requirements.
20x40 Concrete Pad Cost
A 20x40 concrete pad is 800 square feet. At $4 to $8 per square foot, the 20x40 concrete pad cost is about $3,200 to $6,400 for a 4 inch slab. It needs about 9.9 cubic yards at 4 inches, 12.3 at 5 inches and 14.8 at 6 inches, so usually one or two trucks. Common uses are long driveways, RV and boat parking, carports for three vehicles in a line, and small shops. RV pads should be at least 5 to 6 inches thick with rebar. See how thick a concrete driveway should be for vehicle loads.
20x20 Concrete Slab Cost by Finish
| Finish | Cost per sq ft | 20x20 (400 sq ft) | 20x30 (600 sq ft) |
|---|---|---|---|
| Broom finish | $4 – $8 | $1,600 – $3,200 | $2,400 – $4,800 |
| Smooth trowel (garage) | similar, sometimes slightly more | $1,600 – $3,600 | $2,400 – $5,400 |
| Colored or stained | $8 – $12 | $3,200 – $4,800 | $4,800 – $7,200 |
| Stamped | $12 – $18 | $4,800 – $7,200 | $7,200 – $10,800 |
Garage floors can also be coated after curing with epoxy or polyaspartic coatings; that cost is separate from the slab. See concrete coating cost and polished concrete cost.
What Drives the 20x20 Concrete Slab Cost Up or Down
- Thickness: each extra inch adds about 1.2 cubic yards of concrete on a 20x20.
- Reinforcement: rebar costs more than mesh or fiber but adds strength.
- Footings: garages and buildings need thickened edges or footings.
- Site: slopes, poor soil, trees and roots add excavation and base work.
- Access: if a truck cannot reach the forms, a pump adds about $120 to $300 per hour according to Angi, with minimum charges.
- Removal: breaking out an old slab adds about $2 to $6 per square foot.
- Finish: decorative finishes can double or triple the cost.
- Permits: garages and buildings almost always need them.
- Region and season: labor rates and demand vary a lot.
Materials vs Labor in a 20x20 Concrete Slab Cost
On a plain 4 inch 20x20 concrete slab, the ready-mix itself is about $650 to $1,080, or roughly a third of a $2,400 quote. Gravel, forms, mesh and supplies add a few hundred dollars more. The rest, often half or more of the total, is labor and equipment: digging, hauling soil, compacting, setting forms, placing and finishing the concrete, cutting joints, and stripping forms. That is why quotes vary so much between contractors and regions, and why doing the prep yourself can cut the price. It is also why decorative finishes cost so much more: stamping and coloring a 20x20 slab takes extra skilled workers on pour day.
Permits for a 20x20 Slab
Whether you need a permit depends on your town and on what the slab is for. A plain 20x20 patio or parking pad may not need one in some places, but many towns limit impervious surfaces, require setbacks from property lines, or need a permit for any new driveway connection. Slabs for garages, carports, sheds above a certain size and metal buildings almost always need a building permit and inspections. Ask your building department before you pour, and confirm whether the permit fee is part of the 20x20 concrete slab cost in your quote.
DIY 20x20 Concrete Slab Cost
A 20x20 slab is a big step up from a small pad. About 5 cubic yards of concrete, roughly 10 tons, must be placed and finished within an hour or two. Bagged concrete is not practical: it would take about 225 bags of 80 lb mix. DIY usually means ordering ready-mix and having at least four or five experienced helpers.
| DIY item | Approximate cost |
|---|---|
| Ready-mix, about 5.3 yards at $125 – $200 | about $660 – $1,060 |
| Gravel base, about 5 cu yd | varies by area |
| Form lumber and stakes (about 80 linear ft) | often $100 – $200 |
| Wire mesh or rebar for 400 sq ft | often $100 – $300 |
| Tool rentals (compactor, bull float, power screed) | varies |
That often totals roughly $1,000 to $1,800 in materials and rentals, a meaningful saving over $1,600 to $3,200. But finishing 400 square feet of concrete by hand is hard, and mistakes are permanent. Many homeowners do the excavation and forms themselves and hire a finishing crew for pour day.
Crew and Tools for a DIY 20x20 Pour
For a 20x20 slab, plan on at least four or five people on pour day: one or two raking and shoveling, one running the screed, one on the bull float, and one ready to edge and joint. Rent or buy a plate compactor for the base, a bull float with extension handles, a magnesium hand float, an edger, a groover, steel trowels, a stiff broom, and knee boards if you will trowel the slab. A power screed and a walk-behind saw for joints make the job faster. Have plastic sheeting or curing compound ready before the truck arrives.
How to Pour a 20x20 Slab: Key Steps
- Check permits, setbacks and utility locations (call 811).
- Lay out a 20 × 20 square; the diagonals should both be about 28 feet 3.4 inches.
- Excavate, compact the subgrade, and spread and compact the gravel base.
- Set forms with a slope of about 1/8 to 1/4 inch per foot for drainage.
- Place vapor barrier (indoors), reinforcement on chairs, and any anchor bolts or embeds.
- Schedule the ready-mix truck and pump if needed; have the crew and tools ready.
- Place, screed, bull float, edge and finish the concrete.
- Cut or tool control joints into four 10 × 10 foot panels.
- Cure the slab by keeping it moist or applying curing compound.
See how to build concrete forms and how long concrete takes to cure.
Is a 20x20 Slab Big Enough for Two Cars?
A 20 × 20 foot slab fits two average cars side by side, but it is tight. Many garage builders treat 20 × 20 as the minimum two-car size and recommend 22 × 22 or 24 × 24 feet if you want room to open doors fully, store bikes or tools, or park larger SUVs and pickups. Going from 20 × 20 to 24 × 24 adds 176 square feet, which at $4 to $8 per square foot adds roughly $700 to $1,400 to the slab. If you are building a garage, that extra space is usually worth more than it costs. For a parking pad, 20 × 20 works well, especially if you can step off onto a lawn or walkway.
How Long Does a 20x20 Slab Take?
A contractor can usually prep, form and pour a 20x20 slab in two to three days. A typical schedule:
- Day 1: layout, excavation and soil haul-off.
- Day 2: gravel base, compaction, forms, vapor barrier and reinforcement; inspection if required.
- Day 3: pour and finish, usually in a morning; joints cut later that day or the next.
- After the pour: foot traffic in about 1 to 2 days, cars in about 7 days, and design strength at about 28 days.
Garages and buildings may add time for footing inspections and anchor bolt layout.
Weather and Timing
Mild, dry days are best for pouring a 20x20 slab. In hot, windy weather, the surface dries fast and can crack, so crews pour early and may use evaporation retarders. In cold weather, the slab must be protected from freezing with blankets and may need heated concrete or accelerators, which raise the 20x20 concrete slab cost. Avoid pouring right before heavy rain. See pouring concrete in cold weather and can you pour concrete in the rain.
Truck Access and Delivery
About 5 to 8 yards of concrete arrives in one truck that can weigh 30 tons loaded. If the truck can back up to the forms, the concrete goes straight down the chute. If not, plan for wheelbarrows and extra helpers, a conveyor, or a pump. Keep the truck off septic systems, soft lawns and any driveway you want to keep. See how much a yard of concrete weighs.
Common 20x20 Slab Problems and How to Avoid Them
- Random cracks: cut control joints into four 10 × 10 foot panels within a day of the pour.
- Settling at one corner: compact the subgrade and base in layers, and avoid pouring over fresh fill.
- Water pooling: set the forms with a slope; a dead-flat 20x20 slab holds puddles.
- Edge cracks under walls or tires: use thickened edges, especially for garages and parking.
- Scaling in winter: use air-entrained concrete in freeze-thaw areas and avoid salt the first winter.
- Steel at the bottom: set mesh or rebar on chairs near mid-depth.
Replacing an Old 20x20 Slab
Removing an existing 400 square foot slab typically costs about $800 to $2,400 at $2 to $6 per square foot, depending on thickness, rebar and access. A 4 inch slab that size is about 10 tons of debris. Adding a new plain 20x20 slab brings the total to roughly $2,400 to $5,600. If the old slab is sound but sunken, compare with concrete leveling cost; if it is only worn on the surface, see concrete overlay cost. Removal details are in concrete removal cost.
20x20 Concrete Pad Cost by Region and Season
Labor is a large share of a 20x20 concrete pad cost, so prices follow local wages. Expect the upper end of the ranges, or more, in high-cost metro areas, and the lower end in competitive rural and suburban markets near ready-mix plants. Remote sites may pay delivery or zone fees. Spring and early summer are the busiest season, so you may see higher quotes and longer waits; late summer and fall often bring better scheduling.
Maintaining a 20x20 Slab
Seal an outdoor slab after it cures, often after about a month, and reseal every few years. Keep gutters and downspouts from draining onto the edges, fill cracks early, and clean oil spills quickly on parking pads and garage floors. See how to seal concrete and how to remove oil stains from concrete.
Three 20x20 Concrete Slab Cost Examples
Example 1: Plain parking pad
A 20x20 concrete pad, 4 inches thick, broom finish, beside a driveway with easy truck access. Quote: $5.50 per square foot, or $2,200, including base, forms, mesh and finishing.
Example 2: Detached garage slab
A 20x20 garage slab, 5 inches thick with #4 rebar, thickened 12 inch edges, vapor barrier, anchor bolts and a smooth finish. Quote: about $9 per square foot, or $3,600, plus permit fees.
Example 3: Stamped patio
A 20x20 stamped patio in a slate pattern with two colors behind a house, poured with a pump. Quote: about $15 per square foot, or $6,000, plus about $900 for the pump.
20x20 Slab vs Other Options
For parking, a 20x20 gravel pad is much cheaper but needs topping up and is harder to clear of snow. Asphalt is another choice for parking pads; see asphalt vs concrete driveway cost. For patios, pavers cost about $10 to $30 per square foot, or $4,000 to $12,000 for 400 square feet. See paving stones vs concrete.
Ways to Save on a 20x20 Slab
- Do the prep yourself: remove sod, haul debris or set forms if your contractor agrees.
- Pour with other work: add a walkway or apron to the same truck and crew day.
- Choose a broom finish and save decorative work for visible borders.
- Keep the shape simple: a plain rectangle is cheaper to form than curves or steps.
- Plan access so the truck can reach the forms and you avoid a pump.
- Get three quotes with the same thickness, base and reinforcement so the numbers compare fairly.
- Avoid the busiest weeks of spring if your schedule is flexible.
Questions to Ask Contractors
- What thickness, psi mix and reinforcement are included in your 20x20 concrete slab cost?
- How deep is the gravel base, and will it be compacted in layers?
- Are thickened edges or footings included for a garage or building?
- Is a vapor barrier included?
- Where will control joints go, and when will they be cut?
- Are excavation, soil haul-off and permits in the price?
- Will you need a pump, and is it included?
Frequently Asked Questions
How much does a 20x20 concrete slab cost?
About $1,600 to $3,200 installed for a standard 4 inch slab at $4 to $8 per square foot. Garage slabs with rebar and thickened edges often cost $2,400 to $4,000 or more.
How much concrete do I need for a 20x20 slab?
About 4.94 cubic yards at 4 inches, 6.17 at 5 inches and 7.41 at 6 inches, plus 5 to 10 percent for waste.
What is the 20x20 concrete pad cost for a carport?
Usually about $1,600 to $3,200 for a 4 inch pad; more if the carport posts need footings.
How much does a 20x30 concrete slab cost?
About $2,400 to $4,800 for a 4 inch slab at $4 to $8 per square foot, using about 7.4 cubic yards of concrete.
How much is a 20x40 concrete pad?
About $3,200 to $6,400 for a 4 inch pad, using about 9.9 cubic yards. RV pads should be thicker and cost more.
How much does a 20x30 metal building with a concrete slab cost?
Roughly $12,000 to $30,000 installed using HomeGuide's $20 to $50 per square foot range, including the slab. The kit alone is often $6,000 to $15,000.
How much does a 20x20 stamped concrete patio cost?
About $4,800 to $7,200 at $12 to $18 per square foot, depending on pattern and colors.
Can one truck pour a 20x20 slab?
Yes. A 20x20 slab needs about 5 to 8 cubic yards depending on thickness, which fits in one standard 8 to 10 yard truck.
How long does a 20x20 slab take to pour?
The pour and finishing usually take a few hours. With prep, most contractors finish a 20x20 slab in two to three days, and cars can usually park on it after about a week.
Is a 20x20 garage slab different from a patio slab?
Yes. A garage slab usually needs thicker concrete, rebar, thickened edges or footings, anchor bolts, a vapor barrier and a permit, so it costs more than a plain patio slab of the same size.
How thick should a 20x20 slab be?
4 inches for patios and light parking, 5 to 6 inches with rebar for garages, trucks and heavy equipment.
Sources
- Angi, "How much does a concrete slab cost?" angi.com
- HomeAdvisor, "How much does a concrete slab cost?" homeadvisor.com
- HomeGuide, "How much does a metal building cost?" homeguide.com
- HomeGuide, "Concrete driveway cost" (finish ranges) and "Concrete removal cost." homeguide.com
- Angi, "Concrete pumping cost." angi.com
- Image credits: garage floor photo by the Massachusetts Metropolitan District Water Supply Commission, 1938 (public domain), via Wikimedia Commons. Diagram and garage image by Asphapro.com.
Prices checked November 2026. They are national ranges; local prices can be higher or lower.
Related Guides
- How to build concrete forms — layout, stakes and slope
- Types of concrete finishes — broom, trowel, stamped, polished